FFM101 thru ffm107 surface mount fast recovery rectifier reverse voltage - 50 to 1000 volts forward current - 1.0 ampere case : jedec do-214ac molded plastic body t erminals : solder plated, solderable per mil-std-750, method 2026 polarity : color band denotes cathode end mounting position : any w eight :0.003 ounce, 0.093 grams 0.004 ounce, 0.111 grams sma(h) the plastic package carries underwriters laboratory flammability classification 94v-0 for surface mounted applications fast switching for high ef ficiency low reverse leakage built-in strain relief,ideal for automated placement high forward surge current capability high temperature soldering guaranteed: 250 c/10 seconds at terminals fea tures mechanical data characteristic maximum ra tings and electrical characteristics 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 v v v symbols units a a v v rrm v rms v dc i (a v) i fsm v f 1.0 30.0 1.3 operating junction and storage temperature range maximum repetitive peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current 0.375?(9.5mm) lead length at t l = 90 c peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage at 1.0a maximum dc reverse current t a =25 c at rated dc blocking voltage t a =125 c i r 5.0 200.0 c j t j , t stg 20.0 15.0 -65 to +150 pf c t ypical thermal resistance (note 3) c/w t ypical junction capacitance (note 2) maximum reverse recovery time (note 1) t rr 150 250 500 ns ffm 101 ratings at 25 c ambient temperature unless otherwise specified. single phase half-wave 60hz,resistive or inductive load,for capacitive load current derate by 20%. note:1.reverse recovery condition i f =0.5a,i r =1.0a,irr=0.25a 2.measured at 1mhz and applied reverse voltage of 4.0v d.c. 3. p .c.b. mounted with 0.2x0.2 ?(5.0x5.0mm) copper pad areas ffm 102 ffm 103 ffm 104 ffm 105 ffm 106 ffm 107 r j a a dimensions in inches and (millimeters) sma(do-214ac) .0 5 5(1 . 40) . 06 2 (1. 6 0) .11 4 (2. 9 0) .0 9 8(2 . 50) .1 8 1(4 . 60) . 1 57( 4 .00) .01 2 (.3 0 5) .0 0 6(. 1 52) .0 0 2(. 0 51) .0 0 8(.2 0 3) . 20 8 (5. 2 8) .1 8 8(4. 8 0) . 0 79( 2 .0 0 ) .1 0 3( 2 .62) .06 0 (1. 5 2) .0 3 0( 0 .76)
FFM101 thru ffm107 ra tings and characteristic cur ves 1.0 0.8 0.6 0.4 0.2 0 0 25 50 75 100 125 150 175 30 25 20 15 10 5.0 0.6 0.8 1.0 1.2 1.4 1.5 0.1 1.0 10 100 0.01 0.1 1 10 100 100 10 1 0.1 reverse voltage,vol ts t,pulse dura tion,sec. fig. 5-typical junction cap acit ance fig. 6-typical transient thermal impedance fig. 3-typical inst ant aneous for w ard characteristics number of cycles a t 60 hz fig. 2-maximum non-repetitive peak for w ard surge current fig. 1- for w ard current dera ting cur ve , t n e r r u c d e i f i t c e r d r a w r o f e g a r e v a s e r e p m a d r a w r o f s u o e n a t n a t s n i s e r e p m a , t n e r r u c f p , e c n a t i c a p a c n o i t c n u j , t n e r r u c e g r u s d r a w r o f k a e p s e r e p m a inst ant aneous for w ard voleage, vol ts single phase half w ave 60hz resistive or inductive load 1 10 100 8.3ms single half sine-w a ve (jedec method) 0.01 0.1 1 2 0 1 0 t j =25 c pulse width=300 m s 1%duty cycle t j =25 c 1 10 100 200 0 20 40 60 80 100 1,000 100 10 1 0.1 0.01 tj=100 c tj=25 c percent of peak reverse voltage,% fig. 4-typical reverse characteristics , t n e r r u c e s r e v e r s u o e n a t n a t s n i s e r e p m a o r c i m , e c n a d e p m i l a m r e h t t n e i s n a r t w / c ambient tempera ture, c
|
